Description

The Lev’O+ LPG Level solution enables remote reading of LPG gas tank levels. The tank level is measured and transmitted periodically over the LoRaWAN® network to the remote application. The unit is composed of the TORAN’O AtEx zone 1 sensor and a Rochester Gauge.

Characteristics

• LoRaWAN®, Class A
• Ready to install bundle with probe and transmitter.
• Easy to deploy and use.
• Plug & play with TORAN’O device (not supplied)
• Probe power supplied by TORAN’O for the duration of the measurement
• Remote level measurement probe on 2m cable:
  – Output voltage: ratiometric 10-90%
  – Accuracy: +/- 4% of full scale.
  – Horizontal LPG tank (vertical on demand)

Description

The TORAN’O ATEX zone 1 sensor reports status changes, pulse count values and analog measurements of equipment in an ATEX 1 sensitive zone such as water, gas, electricity or thermal energy meters, mechanical pressure switches, pressure transducers. It allows existing equipment to communicate over a public or private LoRaWAN® network.

Characteristics

• LoRaWAN®, Class A
• Easy to install and use
• 3 pulse inputs or status reports
• 3 analog inputs: 2x 0-5V and 1x 4-20mA
• 1 stabilised switched power supply output
• SAFT LS17500 Lithium battery on holder
• Differential data compression
• version IP55 or IP68
• Up to 8 years of autonomy

Description

Configures a fleet of WATTECO IoT devices.

Characteristics

• USB 2.0 interface: compatible with Windows and Linux
• Management and coordination: up to 50 LoRaWAN® sensors
• Self-powered from the USB port
• Online Service  LoRaEncoderConfiguration: https://lora.watteco.fr/Lora/LoraEncoderConfiguration/Index.html
• LoRaUpdater tools donwlod on page: http://support.watteco.com/downloads/

Description

The LEV’O+ Liquid Level solution is used to determine the level of a tank, cistern or cavity, to accurately monitor variations in the level of the liquid and does not require knowledge of its geometric dimensions. By measuring the relative pressure of the liquid (water, fuel, oil, liquid fertiliser, etc.), LEV’O+ transmits the data over a public or private LoRaWAN® radio network, thus enabling the application to establish the relationship between the analog value and the height of the liquid.

Characteristics

• Easy to deploy and use
• Plug & play with TORAN’O device (not supplied)
• Probe power supplied by TORAN’O for the duration of the measurement
• Remote level measurement probe on 5m cable:
  – Pressure range: 0…0.3 bar
  – Accuracy: +/- 0.8% of full scale
  – Resolution: 0.1% of full scale
  – Relative sensor 4-20mA
  – Suitable for fitting in 1-inch pipe

Description

CLOS’O is a LoRaWAN® sensor that determines if a gateway is properly closed. Installed on the frame (or on the fixed part), it detects the position of a magnet fixed on the gate’s moving part.

The sensor reports over a public or private LoRaWAN® radio network the open or closed state of the gate. An alert is transmitted if the sensor is pulled out.

Characteristics

• LoRaWAN®, Class A
• Autonomous sensor
• Detection of gate opening and closing
• Large detection distance: up to 35mm
• Sensor pullout alert
• Very simple installation
• More than 5 years of autonomy
• Set intended for outdoor use

Description

The SMARTPILOT WIRE is a Class C LoRaWAN® actuator that monitors and controls up to 6 operating modes for any electric heater as well as any active load (ON/OFF) driven by a relay.

Characteristics

• LoRaWAN®, Class C
• Easy to use and deploy
• Active load monitoring and control
• Data compression for batch status report
• Class II protection

Description

SMARTPLUG is a LoRaWAN® Class C smart device that monitors and controls plugged equipment. It monitors and sends reports about power line quality.

Characteristics

• LoRaWAN®, Class C
• Easy to use and deploy.
• Up to 3500W – 16A switch On/Off capability.
• Monitor and report Power/Energy/Voltage/Frequency.
• Socket types E, F and G available.

Description

The Pulse SENS’O ATEX zone 1 remotely reads metering data from water, gas, electricity or heat meters in ATEX zone 1 sensitive areas. Pulse SENS’O allows you to make all your mechanical pressure switches communicate with one another in ATEX zone 1 explosive atmospheres. It transforms existing meters into communicating meters via a public or private LoRaWAN® network.

Different versions available:

• Outdoor remote Pulse Sens’O
• Waterproof remote Pulse Sens’O

Characteristics

• LoRaWAN®, Class A
• Easy to install and use
• 3 pulse inputs or status reports
• SAFT LS17500 Lithium battery on holder
• Differential data compression
• Version IP55 or IP68
• Optional external antenna connector available
• 10 years of autonomy (data compression mode)

Description

The IP68 waterproof remote Pulse Sens’O is used to remotely read the metering data from a water meter using a module clipped to the meter. It turns existing meters into smart meters via a public or private LoRaWAN® network.

Different versions available:

• Outdoor remote Pulse Sens’O
• AtEx zone 1 outdoor remote Pulse Sens’O

Characteristics

• LoRaWAN®, Class A
• Easy to install and use
• 3 pulse inputs
• Differential data compression
• 12 years of autonomy (data compression mode)
• IP55

Description

FLASH’O is a LoRaWAN® meter interface that transmits the accumulated number of LED flashes from any pulse meter: water, gas, electricity, energy.

Characteristics

• LoRaWAN®, Class A
• Easy to use and deploy
• Data compression for batch report
• IP55
• Battery autonomy up to 12 years
• Up to 500 pulses/second Flash LED rate counting